Skocz do zawartości

GI Xpeed LX2


Gość bysiu
 Udostępnij

Rekomendowane odpowiedzi

Witam.

Chciałem dziś zainstalować Graterlię w tytułowym tunerze,jednak bez powodzenia.

Tuner startuje i stoi na planszy GOS z napisem BOOTING na wyświetlaczu(czekałem ok.7min).

Pozdrawiam.

 

Oprócz biało czerwonego napisu GOS i adresu forum nic innego tam nie ma.

 

https://zapodaj.net/bb9b6789f94b5.jpg.html

Odnośnik do komentarza
Udostępnij na innych stronach

  • 1 rok później...

Xpeed LX1 też mam problem podpinam się pod temat.

Próba instalacji z pendriva wszystko się wgrywa ładnie do napisu : "done" następnie przechodzi na "load" i na tym koniec , sumy kontrolne sprawdziłem i się zgadzają , image konkurencyjne się instalują i uruchamiają nie wiem co możne być problemem , bodloader oryginalny nie zmieniany.

Odnośnik do komentarza
Udostępnij na innych stronach

Z tego co pamiętam to LX1 i LX2 niewiele się różniły i oba działały (potwierdzone przez użytkowników). Ostatnio jednak pobrań nie było. Nie ma nikogo z devel aby sprawdzić bo Tunera nie mamy.

Aby Ci pomoc potrzebuję informacji ze złącza RS232 w tunerze. Nie mam pojęcia na czym on się zatrzymuje :(

Odnośnik do komentarza
Udostępnij na innych stronach

Jakich informacji dokładnie potrzebujesz o RS232 ?

 

Aha, nie dodałem, że kupiłem 3 szt. tych tunerów bo rezygnuje z nbox i na każdym z nich nie odpala "GOS".

 

Rozkręcenie Xpeed LX1 i  foty makro potrzebne ?

Odnośnik do komentarza
Udostępnij na innych stronach

Raczej nie fotki nie.

Z RS-232 będzie normalna konsola txt. Także będzie widać jak się uruchamia "pudełko" i w którym miejscu staje.

Być może poprawki kernela są winne jak kiedyś dla Vu+ Ultimo. Ale nic więcej nie mogę napisać bez loga z RS-232 :(

Zawsze jak się da to pomagam.

Przy czym mała informacja - przez najbliższe 2-3 dni nie wszystko będę mógł zrobić ponieważ muszę zreplikować dwa dyski z macierzy. Niestety "zmarły" w poniedziałek ;(

Odnośnik do komentarza
Udostępnij na innych stronach

Próbować tego : Narzędzia PC dla tunerów GI Voyager

Oprogramowanie do zainstalowania na komputerach do komunikacji z tunerami Golden Interstar Voyager. Przy jego pomocy można wgrać oprogramowanie fabryczne do tunera wykorzystując port RS 232. Analogicznie można dokonać "zrzutu" zawartości pamieci tunera na komputer. Przydatne w sytuacji, kiedy z różnych względów tuner nie włącza się w tryb pracy przy sprawnym zasilaniu. Kabel połączeniowy tuner-PC "null modem" (2-3;3-2;5-5)  czy szukać innego oprogramowania jaka podpowiedz ?  putty lub hyper terminal ?

Odnośnik do komentarza
Udostępnij na innych stronach

Potrzebujesz kabel RS-232 <--> RS232 lub RS232 <--> USB.

Potem konfigurujesz putty do pracy z RS-232 i odpalasz terminal. Włączasz tuner i patrzysz co się dzieje.

Niestety nie znam parametrów RS-232 w GI. Trzeba by zgłębić temat. Chodzi o przepustowość, bity parzystości itp. dane.

Odnośnik do komentarza
Udostępnij na innych stronach

Udało się ustawić kabel Null Modem prędkość 115200 PuTTy lub HiperTerminal.

 

 

 

BCM73580001

1 00000001

234#!@

M0

WLCT 0000000001

 

 

SHMOO VER MSA 16b 1.12

 

PKID 16020112 20120406 003B6000 003B0000 001B103F 00001C00

 

S300001B3

S000011C0

 

RDLY  WL 0 0000000004

 

RDEN  WL 0 0000000035

 

RDQS  WL 0

 

    0000000000111111111122222222223333333333444444444455555555556666

    0123456789012345678901234567890123456789012345678901234567890123

00 ----------+++++++++++++++++++++++++X+++++++++++++++++++++++++---

01 --------------------++++++++++++++++++++++X+++++++++++++++++++++

02 ----------+++++++++++++++++++++++++++X++++++++++++++++++++++++--

03 ------------++++++++++++++++++++++++++X+++++++++++++++++++++++--

04 --------+++++++++++++++++++++++++X++++++++++++++++++++++++------

05 --------------+++++++++++++++++++++++++X+++++++++++++++++++++++-

06 --------+++++++++++++++++++++++++X++++++++++++++++++++++++------

07 --------------+++++++++++++++++++++++++X++++++++++++++++++++++--

08 -------+++++++++++++++++++++++++X++++++++++++++++++++++++-------

09 ---------++++++++++++++++++++++++X++++++++++++++++++++++++------

10 ------+++++++++++++++++++++++++X++++++++++++++++++++++++--------

11 ---------+++++++++++++++++++++++++X+++++++++++++++++++++++++----

12 ----+++++++++++++++++++++++++X+++++++++++++++++++++++++---------

13 -------++++++++++++++++++++++++X++++++++++++++++++++++++--------

14 ------+++++++++++++++++++++++++X+++++++++++++++++++++++++-------

15 -------++++++++++++++++++++++++X++++++++++++++++++++++++--------

 

 

P  WL 0

 

    0000000000111111111122222222223333333333444444444455555555556666

    0123456789012345678901234567890123456789012345678901234567890123

00 ----++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++

01 -------------+++++++++++++++++++++++++X+++++++++++++++++++++++++

02 ----++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++

03 -------++++++++++++++++++++++++++++X++++++++++++++++++++++++++++

04 ++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++

05 -------++++++++++++++++++++++++++++X++++++++++++++++++++++++++++

06 -+++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++

07 --------++++++++++++++++++++++++++++X+++++++++++++++++++++++++++

08 -----+++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++

09 -------++++++++++++++++++++++++++++X++++++++++++++++++++++++++++

10 ----++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++

11 --------++++++++++++++++++++++++++++X+++++++++++++++++++++++++++

12 --+++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++

13 ------+++++++++++++++++++++++++++++X++++++++++++++++++++++++++++

14 ---++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++

15 -----+++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++

 

 

N  WL 0

 

    0000000000111111111122222222223333333333444444444455555555556666

    0123456789012345678901234567890123456789012345678901234567890123

00 ----------+++++++++++++++++++++++++X+++++++++++++++++++++++++---

01 --------------------++++++++++++++++++++++X+++++++++++++++++++++

02 ----------+++++++++++++++++++++++++++X++++++++++++++++++++++++--

03 ------------++++++++++++++++++++++++++X+++++++++++++++++++++++--

04 -------+++++++++++++++++++++++++X+++++++++++++++++++++++++------

05 --------------+++++++++++++++++++++++++X++++++++++++++++++++++++

06 ---------++++++++++++++++++++++++X++++++++++++++++++++++++------

07 --------------+++++++++++++++++++++++++X+++++++++++++++++++++++-

08 -------+++++++++++++++++++++++++X++++++++++++++++++++++++-------

09 --------+++++++++++++++++++++++++X++++++++++++++++++++++++------

10 ------+++++++++++++++++++++++++X++++++++++++++++++++++++--------

11 ---------+++++++++++++++++++++++++X+++++++++++++++++++++++++----

12 ----+++++++++++++++++++++++++X+++++++++++++++++++++++++---------

13 -------++++++++++++++++++++++++X++++++++++++++++++++++++--------

14 ------+++++++++++++++++++++++++X+++++++++++++++++++++++++-------

15 -------++++++++++++++++++++++++X++++++++++++++++++++++++--------

 

 

WRDQ  WL 0

 

    0000000000111111111122222222223333333333444444444455555555556666

    0123456789012345678901234567890123456789012345678901234567890123

00 +++++++++++++++++++++X++++++++++++++++++++-------+++++++++++++++

01 -++++++++++++++++++++++X+++++++++++++++++++++----------+++++++++

02 ++++++++++++++++++++++X++++++++++++++++++++++----+++++++++++++++

03 ++++++++++++++++++++++X++++++++++++++++++++++------+++++++++++++

04 +++++++++++++++++++++X+++++++++++++++++++++-------++++++++++++++

05 ++++++++++++++++++++++X++++++++++++++++++++++----+++++++++++++++

06 ++++++++++++++++++++++X+++++++++++++++++++++------++++++++++++++

07 ++++++++++++++++++++++X++++++++++++++++++++++-----++++++++++++++

08 +++++++++++++++++++++X++++++++++++++++++++-------+++++++++++++++

09 ++++++++++++++++++++++X+++++++++++++++++++++-----+++++++++++++++

10 +++++++++++++++++++++X+++++++++++++++++++++------+++++++++++++++

11 ++++++++++++++++++++++X+++++++++++++++++++++-----+++++++++++++++

12 +++++++++++++++++++++X+++++++++++++++++++++------+++++++++++++++

13 ++++++++++++++++++++++X+++++++++++++++++++++-----+++++++++++++++

14 ++++++++++++++++++++++X++++++++++++++++++++++----+++++++++++++++

15 ++++++++++++++++++++++X+++++++++++++++++++++-------+++++++++++++

 

 

WRDM  WL 0 0000000021

WRDM  WL 0 0000000021

 

 

ADDR

 

    0000000000111111111122222222223333333333444444444455555555556666

    0123456789012345678901234567890123456789012345678901234567890123

00 +++++++++++++++++S+++++++++X+++++++++++++++++++++++++++---------

 

B03B6054

567#!@#@

 

BCM97358A1 CFE v4.144, CFE core v4.29, Endian Mode: Little

Build Date: Mon Jul  7 08:24:59 CEST 2014 (paul@ini)

Copyright © Broadcom Corporation.

 

Enabling NAND flash at CS2.

BCHP_NAND_FLASH_DEVICE_ID =0xecdc1095, BCHP_NAND_FLASH_DEVICE_ID_EXT = 0x55ececdc

CPU speed:      751MHz

Total memory(0): 512MB

DDR Freq:        800 MHz

DDR Mode:        DDR3

MEMC 0 DEV SIZE: 2GBIT

MEMC 0 DDR Width:16

MEMC 0 DEV Width:8

Boot Device:    SPI

Total flash:    4MB

 

Initializing USB.

USB: Locating Class 09 Vendor 0000 Product 0000: USB Root Hub

 

CFE initialized.

USB device matching <USB Disk> not found!

 

[FLASH-TOOL] Searching update files...

 

[FLASH-TOOL] Could not init file system: Device not found

 

[FLASH-TOOL] There are not any update files...

 

Booting...

Starting splash screen.

Found splash image - Width = 720 Height = 480

Non Interlaced Replace list 043e8680 0c800000Interlaced Replace list 043e8c20 0c8005a0

Loader:elf Filesys:raw Dev:nandflash0.kernel File: Options:ubi.mtd=0 root=ubi0:rootfs rootfstype=ubifs rw bmem=256M@512M

Loading: 0x80001000/9064952 0x808a61f8/161560 Entry address is 0x806d4020

Starting program at 0x806d4020

 

Initializing cgroup subsys cpuset

Linux version 3.12.1 (oe-user@oe-host) (gcc version 6.3.0 (GCC) ) #1 Fri Apr 27 20:23:27 CEST 2018

Fetching vars from bootloader... found 10 vars.

Options: enet_en=1 enet0_mii=0 enet_no_mdio=0 enet1_en=0 moca=0

        sata=0 docsis=0 pci=0 pcie=0 smp=0 usb=1

Using 512 MB + 0 MB RAM (from CFE)

MEMC0 split: 256 MB -> Linux; 256 MB -> extra bmem

CPU revision is: 00029032 (Broadcom BMIPS3300)

Determined physical RAM map:

memory: 10000000 @ 00000000 (usable)

bmem: adding 16 MB RESERVED region at 240 MB (0x01000000@0x0f000000)

Zone ranges:

  Normal  [mem 0x00000000-0x0fffffff]

Movable zone start for each node

Early memory node ranges

  node  0: [mem 0x00000000-0x0fffffff]

Primary instruction cache 32kB, VIPT, 4-way, linesize 16 bytes.

Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes

Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 65024

Kernel command line: ubi.mtd=0 root=ubi0:rootfs rootfstype=ubifs rw bmem=256M@512M ubi.mtd=rootfs rootfstype=ubifs root=ubi0:rootfs bmem=256M@512M bmem=16M console=ttyS0,115200n8

PID hash table entries: 1024 (order: 0, 4096 bytes)

Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)

Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)

Memory: 234452K/262144K available (7028K kernel code, 307K rwdata, 1312K rodata, 232K init, 118K bss, 27692K reserved)

NR_IRQS:160

Detected MIPS clock frequency: 751 MHz (375.763 MHz counter)

Console: colour dummy device 80x25

Calibrating delay loop... 749.56 BogoMIPS (lpj=374784)

pid_max: default: 32768 minimum: 301

Mount-cache hash table entries: 512

devtmpfs: initialized

bmem: adding extra 256 MB RESERVED region at 512 MB (0x10000000@0x20000000)

NET: Registered protocol family 16

USB0: power enable is active low; overcurrent is active low

bio: create slab <bio-0> at 0

SCSI subsystem initialized

usbcore: registered new interface driver usbfs

usbcore: registered new interface driver hub

usbcore: registered new device driver usb

Linux video capture interface: v2.00

Advanced Linux Sound Architecture Driver Initialized.

Bluetooth: Core ver 2.16

NET: Registered protocol family 31

Bluetooth: HCI device and connection manager initialized

Bluetooth: HCI socket layer initialized

Bluetooth: L2CAP socket layer initialized

Bluetooth: SCO socket layer initialized

cfg80211: Calling CRDA to update world regulatory domain

Switched to clocksource wktmr

FS-Cache: Loaded

NET: Registered protocol family 2

TCP established hash table entries: 2048 (order: 2, 16384 bytes)

TCP bind hash table entries: 2048 (order: 1, 8192 bytes)

TCP: Hash tables configured (established 2048 bind 2048)

TCP: reno registered

UDP hash table entries: 256 (order: 0, 4096 bytes)

UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)

NET: Registered protocol family 1

RPC: Registered named UNIX socket transport module.

RPC: Registered udp transport module.

RPC: Registered tcp transport module.

RPC: Registered tcp NFSv4.1 backchannel transport module.

FS-Cache: Netfs 'nfs' registered for caching

NFS: Registering the id_resolver key type

Key type id_resolver registered

Key type id_legacy registered

Installing knfsd (copyright © 1996 okir@monad.swb.de).

FS-Cache: Netfs 'cifs' registered for caching

Key type cifs.spnego registered

fuse init (API version 7.22)

SGI XFS with security attributes, realtime, large block/inode numbers, no debug enabled

msgmni has been set to 457

io scheduler noop registered

io scheduler cfq registered (default)

Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled

serial8250.0: ttyS0 at MMIO 0x10406800 (irq = 62, base_baud = 5062500) is a 16550A

console [ttyS0] enabled

serial8250.0: ttyS1 at MMIO 0x10406840 (irq = 63, base_baud = 5062500) is a 16550A

serial8250.0: ttyS2 at MMIO 0x10406880 (irq = 64, base_baud = 5062500) is a 16550A

loop: module loaded

brcmstb_nand: NAND controller driver is loaded

Config internal EPHY through MDIO

usbcore: registered new interface driver zd1201

ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver

ehci-brcm ehci-brcm.0: Broadcom STB EHCI

ehci-brcm ehci-brcm.0: new USB bus registered, assigned bus number 1

ehci-brcm ehci-brcm.0: irq 66, io mem 0x10480300

ehci-brcm ehci-brcm.0: USB 0.0 started, EHCI 1.00

hub 1-0:1.0: USB hub found

hub 1-0:1.0: 2 ports detected

ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver

ohci-brcm ohci-brcm.0: Broadcom STB OHCI

ohci-brcm ohci-brcm.0: new USB bus registered, assigned bus number 2

ohci-brcm ohci-brcm.0: irq 67, io mem 0x10480400

hub 2-0:1.0: USB hub found

hub 2-0:1.0: 2 ports detected

usbcore: registered new interface driver usb-storage

mousedev: PS/2 mouse device common for all mice

i2c /dev entries driver

usbcore: registered new interface driver btusb

hidraw: raw HID events driver © Jiri Kosina

usbcore: registered new interface driver usbhid

usbhid: USB HID core driver

TCP: cubic registered

NET: Registered protocol family 10

NET: Registered protocol family 17

Bluetooth: HIDP (Human Interface Emulation) ver 1.2

Bluetooth: HIDP socket layer initialized

Key type dns_resolver registered

EBI CS2: setting up NAND flash (primary)

NAND device: Manufacturer ID: 0xec, Chip ID: 0xdc (Samsung NAND 512MiB 3,3V 8-bit), 512MiB, page size: 2048, OOB size: 64

brcmnand brcmnand.0: 512MiB total, 128KiB blocks, 2KiB pages, 16B OOB, 8-bit, BCH-1

 

Bad block table found at page 262080, version 0x01

Bad block table found at page 262016, version 0x01

Creating 3 MTD partitions on "brcmnand.0":

0x000000000000-0x00001f900000 : "rootfs"

0x000000000000-0x000020000000 : "entire_device"

0x00001f900000-0x00001ff00000 : "kernel"

EBI CS0: setting up SPI flash

spi_brcmstb spi_brcmstb.0: master is unqueued, this is deprecated

spi_brcmstb spi_brcmstb.0: 1-lane output, 3-byte address

m25p80 spi0.0: found s25sl032p, expected m25p80

m25p80 spi0.0: s25sl032p (4096 Kbytes)

Creating 6 MTD partitions on "spi0.0":

0x000000000000-0x000000080000 : "cfe"

0x000000080000-0x000000280000 : "splash"

0x000000280000-0x000000300000 : "macadr"

0x000000300000-0x000000380000 : "nvram"

0x000000380000-0x0000003c0000 : "bootconfig"

0x0000003c0000-0x000000400000 : "facconfig"

PM: CP0 COUNT/COMPARE frequency depends on divisor

UBI: attaching mtd0 to ubi0

UBI: scanning is finished

UBI: attached mtd0 (name "rootfs", size 505 MiB) to ubi0

UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes

UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048

UBI: VID header offset: 2048 (aligned 2048), data offset: 4096

UBI: good PEBs: 4040, bad PEBs: 0, corrupted PEBs: 0

UBI: user volume: 1, internal volumes: 1, max. volumes count: 128

UBI: max/mean erase counter: 2/0, WL threshold: 4096, image sequence number: 531752739

UBI: available PEBs: 0, total reserved PEBs: 4040, PEBs reserved for bad PEB handling: 80

UBI: background thread "ubi_bgt0d" started, PID 49

UBI error: ubi_attach_mtd_dev: mtd0 is already attached to ubi0

UBI error: ubi_init: cannot attach mtd0

ALSA device list:

  No soundcards found.

UBIFS: background thread "ubifs_bgt0_0" started, PID 50

UBIFS: recovery needed

UBIFS: recovery completed

UBIFS: mounted UBI device 0, volume 0, name "rootfs"

UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes

UBIFS: FS size: 500920320 bytes (477 MiB, 3945 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs)

UBIFS: reserved for root: 0 bytes (0 KiB)

UBIFS: media format: w4/r0 (latest is w4/r0), UUID 4CC358B1-F824-4C0C-AA29-936C6BB4D1C1, small LPT model

VFS: Mounted root (ubifs filesystem) on device 0:10.

devtmpfs: mounted

Freeing unused kernel memory: 232K (80876000 - 808b0000)

Algorithmics/MIPS FPU Emulator v1.5

INIT: version 2.88 booting

-------------------------

Starting Graterlia OS....

-------------------------

 

[*] Mount virtual filesystems...

Starting udev

udevd[73]: starting version 3.2.7

udevd[73]: specified group 'kvm' unknown

udevd[74]: starting eudev-3.2.7

[*] Mount /dev/pts filesystems...

Loading modules: dvb dvb: module_layout: kernel tainted.

Disabling lock debugging due to kernel taint

[platform_i2c_mutex_init] ...

{113}machine = 230

fb0: bcmfb frame buffer device

{113}[mcu_i2c_check_blade1128a] blade1128

input: dreambox front panel as /devices/virtual/input/input0

input: dreambox advanced remote control (native) as /devices/virtual/input/input1

DVB: registering new adapter (dvb)

{113}[fe_attach] (slot = 0) i2cIndex = -1 out of range

dvb dvb.0: DVB: registering adapter 0 frontend 0 (DVB-S2 INTERNAL)...

{113}[semcoAPI_TDA18250A_Init] (1) tmbslTDA18250A_HwInit err: 1

{113}[DNOQ44QAH109A_Open] (1) SemcoAPI_TDA18250A_Init fail.

 

[*] Start filesystems check...

Filesystems OK

[*] Mounting local filesystems...

[*] Saving dmesg to /var/log/dmesg

[*] Initializing random number generator...

[*] Set hostname...

[*] Starting Misc and other script...

net.ipv4.conf.default.rp_filter = 1

net.ipv4.conf.all.rp_filter = 1

INIT: Entering runlevel: 5

BKNI_P_GetTrackAllocEntry_resize: resizing from 4096->8192

BKNI_Malloc(linuxkernel) top users:

    blocks,  bytes, filename:line

      872,  59296, refsw_release_97358_20120313/nexus/base/src/nexus_base_scheduler.c:625

      432,  17280, ../magnum/basemodules/mem/bmem_system.c:286

      364,  17472, magnum/portinginterface/vdc/7358/bvdc_bufferheap_priv.c:737

      324,  83016, ../BSEAV/lib/utils/balloc.c:35

      293,  35160, magnum/commonutils/mrc/7358/bmrc_monitor.c:940

Configuring network interfaces...

connect: Network is unreachable

NTP synchronization failed

eth0 Link DOWN.

IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready

eth0: waiting for carrier

eth0 Link UP.

Auto config phy

eth0: Link is up, 100 Mbps Full Duplex

IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready

eth0: carrier acquired

DUID 00:01:00:01:c7:92:bc:9d:00:1a:a0:00:05:1b

eth0: IAID a0:00:05:1b

eth0: adding address fe80::6d58:df7:e32c:f5e4

eth0: soliciting an IPv6 router

eth0: rebinding lease of 192.168.100.11

eth0: probing address 192.168.100.11/24

eth0: leased 192.168.100.11 for 259200 seconds

eth0: adding route to 192.168.100.0/24

eth0: adding default route via 192.168.100.1

forked to background, child pid 214

NTP synchronization...

No route to pool.ntp.org...wait 5 seconds

NTP synchronization...

done.

Starting OpenBSD Secure Shell server: sshd

done.

[*] Mounting remote filesystems...

[*] Starting rc.local...

Starting crond: OK

INIT: no more processes left in this runlevel

 

 

Odnośnik do komentarza
Udostępnij na innych stronach

Dołącz do dyskusji

Możesz dodać zawartość już teraz a zarejestrować się później. Jeśli posiadasz już konto, zaloguj się aby dodać zawartość za jego pomocą.

Gość
Dodaj odpowiedź do tematu...

×   Wklejono zawartość z formatowaniem.   Usuń formatowanie

  Dozwolonych jest tylko 75 emoji.

×   Odnośnik został automatycznie osadzony.   Przywróć wyświetlanie jako odnośnik

×   Przywrócono poprzednią zawartość.   Wyczyść edytor

×   Nie możesz bezpośrednio wkleić grafiki. Dodaj lub załącz grafiki z adresu URL.

 Udostępnij

×
×
  • Dodaj nową pozycję...