sImBa

Witam ponownie. Faktycznie, monitorując wyjście debug, nie byłem wystarczająco szybki, by połączyć się Hyper Terminalem i umknęło mi to co najistotniejsze. Tym razem log był bardziej "wylewny". ************************************************************* ************************************************ Board - STi7100 Uboot with Boot selection -=*[ B4Team ]*=- ************************************************ ************************************************************* U-Boot 1.3.1 (Mar 11 2012 - 14:25:54) - stm23_0057 DRAM: 128 MiB NOR: 4 MiB NAND: 64 MiB In: serial Out: serial Err: serial Hit any key to stop autoboot: 0 ADB_Box> version U-Boot 1.3.1 (Mar 11 2012 - 14:25:54) - stm23_0057 ADB_Box> fli Bank # 1: CFI conformant FLASH (16 x 16) Size: 4 MiB in 71 Sectors Intel Standard command set, Manufacturer ID: 0x20, Device ID: 0x0A Erase timeout: 8192 ms, write timeout: 1 ms Buffer write timeout: 1 ms, buffer size: 8 bytes Sector Start Addresses: A0000000 RO A0010000 RO A0020000 RO A0030000 RO A0040000 RO A0050000 RO A0060000 RO A0070000 E RO A0080000 RO A0090000 RO A00A0000 RO A00B0000 RO A00C0000 E RO A00D0000 E RO A00E0000 RO A00F0000 E RO A0100000 RO A0110000 RO A0120000 RO A0130000 RO A0140000 RO A0150000 E RO A0160000 E RO A0170000 E RO A0180000 E RO A0190000 E RO A01A0000 E RO A01B0000 E RO A01C0000 RO A01D0000 E RO A01E0000 E RO A01F0000 E RO A0200000 RO A0210000 RO A0220000 RO A0230000 RO A0240000 RO A0250000 RO A0260000 RO A0270000 E RO A0280000 RO A0290000 RO A02A0000 RO A02B0000 RO A02C0000 E RO A02D0000 E RO A02E0000 RO A02F0000 E RO A0300000 RO A0310000 RO A0320000 RO A0330000 RO A0340000 RO A0350000 E RO A0360000 E RO A0370000 E RO A0380000 E RO A0390000 E RO A03A0000 E RO A03B0000 E RO A03C0000 RO A03D0000 E RO A03E0000 E RO A03F0000 E RO A03F2000 E RO A03F4000 E RO A03F6000 E RO A03F8000 E RO A03FA000 E RO A03FC000 E RO A03FE000 E RO ADB_Box> bdinfo boot_params = 0x87DDFF88 memstart = 0x84000000 memsize = 0x08000000 (128 MiB) flashstart = 0xA0000000 flashsize = 0x00400000 ( 4 MiB) flashoffset = 0x00032150 ethaddr = 00:01:01:01:01:01 ip_addr = 192.168.0.102 baudrate = 115200 bps STb7100 version 3.x [29-bit mode] PLL0 = 531 MHz PLL1 = 384 MHz ST40 CPU = 265 MHz ST40 BUS = 132 MHz ST40 PER = 66 MHz ST231 CPU = 384 MHz ST BUS = 192 MHz EMI = 96 MHz LMI = 192 MHz #EMI Banks = 5 EMI #0 CSA = 0xA0000000 ... 0xA03FFFFF ( 4 MiB) EMI #1 CSB = 0xA0400000 ... 0xA07FFFFF ( 4 MiB) EMI #2 CSC = 0xA0800000 ... 0xA0BFFFFF ( 4 MiB) EMI #3 CSD = 0xA0C00000 ... 0xA0FFFFFF ( 4 MiB) EMI #4 CSE = 0xA1000000 ... 0xA7FFFFFF (112 MiB) ADB_Box> coninfo List of available devices: serial 80000003 SIO stdin stdout stderr Wydaje mi się w takim razie, że mam na pokładzie multi-uboota: Nbox Duo_Multiboot FreeBoxB4_team 03_2012 Wersja1b. Teraz ostatnie pytanie i daje Wam spokój. W archiwum tego uboota mam katalog ENV a w nim 2 podkatalogi z ENV do "B4team" i "Freebox env bez mac". Mam załadować oba img, czy tylko pierwszy? Teraz mam mieszane uczucia, bo nie jestem na 100% pewien które menu było wcześniej. Bardziej przypomina mi się to pierwsze ale tam nie ma domyślnie dopisanej pozycji NAND i było HDD2. I bardzo prawdopodobne, że po wybraniu z menu wyboru urządzenia do startu systemu tego: set bootkern_1 'protect off all; erase a02e0000 a02fffff; reset' posypało mi się ENV. Z góry dzięki za pomoc. Mam nadzieję że dzisiaj w końcu zamknę ten rozdział i odetchnę. B4team: set bootdesc_0 'HDD1 ' set bootcmd_0 'set bootdesc_default 0; saveenv; run bootargs_0; run bootkern_0' set bootkern_0 'ide reset; ext2load ide 0:1 a5000000 /boot/uImage; bootm a5000000' set bootargs_0 'set bootargs console=ttyAS0,115200 root=/dev/sda1 rw ip=$ipaddr:$gatewayip:$serverip:$netmask:eth0:off mem=128m coprocessor_mem=4m@0x10000000,4m@0x10400000 rootdelay=6 nwhwconf=device:eth0,hwaddr:$ethaddr init=/bin/devinit' set bootdesc_1 'F-B ' set bootcmd_1 'run bootkern_1' set bootkern_1 'protect off all; erase a02e0000 a02fffff; reset' set bootdesc_2 'USH1 ' set bootcmd_2 'set bootdesc_default 2; saveenv; run bootargs_2; run bootkern_2' set bootkern_2 'usb reset; ext2load usb 0:1 a5000000 /boot/uImage; bootm a5000000' set bootargs_2 'set bootargs console=ttyAS0,115200 root=/dev/sdb1 rw ip=$ipaddr:$gatewayip:$serverip:$netmask:eth0:off mem=128m coprocessor_mem=4m@0x10000000,4m@0x10400000 rootdelay=6 nwhwconf=device:eth0,hwaddr:$ethaddr init=/bin/devinit' set bootdesc_3 'USH2 ' set bootcmd_3 'set bootdesc_default 3; saveenv; run bootargs_3; run bootkern_3' set bootkern_3 'usb reset; ext2load usb 0:2 a5000000 /boot/uImage; bootm a5000000' set bootargs_3 'set bootargs console=ttyAS0,115200 root=/dev/sdb2 rw ip=$ipaddr:$gatewayip:$serverip:$netmask:eth0:off mem=128m coprocessor_mem=4m@0x10000000,4m@0x10400000 rootdelay=6 nwhwconf=device:eth0,hwaddr:$ethaddr init=/bin/devinit' set bootdesc_4 'USB1 ' set bootcmd_4 'set bootdesc_default 4; saveenv; run bootargs_4; run bootkern_4' set bootkern_4 'usb reset; ext2load usb 0:1 a5000000 /boot/uImage; bootm a5000000' set bootargs_4 'set bootargs console=ttyAS0,115200 root=/dev/sda1 rw ip=$ipaddr:$gatewayip:$serverip:$netmask:eth0:off mem=128m coprocessor_mem=4m@0x10000000,4m@0x10400000 rootdelay=6 nwhwconf=device:eth0,hwaddr:$ethaddr init=/bin/devinit' set bootdesc_5 'USB2 ' set bootcmd_5 'set bootdesc_default 5; saveenv; run bootargs_5; run bootkern_5' set bootkern_5 'usb reset; ext2load usb 0:2 a5000000 /boot/uImage; bootm a5000000' set bootargs_5 'set bootargs console=ttyAS0,115200 root=/dev/sda2 rw ip=$ipaddr:$gatewayip:$serverip:$netmask:eth0:off mem=128m coprocessor_mem=4m@0x10000000,4m@0x10400000 rootdelay=6 nwhwconf=device:eth0,hwaddr:$ethaddr init=/bin/devinit' set bootdesc_6 'USB3 ' set bootcmd_6 'set bootdesc_default 6; saveenv; run bootargs_6; run bootkern_6' set bootkern_6 'usb reset; ext2load usb 0:3 a5000000 /boot/uImage; bootm a5000000' set bootargs_6 'set bootargs console=ttyAS0,115200 root=/dev/sda3 rw gateway=$gatewayip ip=$ipaddr:$gatewayip:$serverip:$netmask:eth0:off mem=128m coprocessor_mem=4m@0x10000000,4m@0x10400000 rootdelay=6 nwhwconf=device:eth0,hwaddr:$ethaddr init=/bin/devinit' set bootdesc_7 'N-b4 ' set bootcmd_7 'set bootdesc_default 7; saveenv; run bootargs_7; run bootkern_7' set bootkern_7 'nand read.i 0xa5000000 0x0 0x300000; bootm a5000000' set bootargs_7 'set bootargs console=ttyAS0,115200 root=/dev/mtdblock3 rw rootfstype=jffs2 ip=$ipaddr:$gateway:$serverip:$netmask:eth0:off mem=128m coprocessor_mem=4m@0x10000000,4m@0x10400000 nwhwconf=device:eth0,hwaddr:$ethaddr init=/bin/devinit' set bootdesc_8 'N-Fb ' set bootcmd_8 'set bootdesc_default 8; saveenv; run bootargs_8; run bootkern_8' set bootkern_8 'nand read.i 0xa5000000 0x3c00000 0x300000; bootm a5000000' set bootargs_8 'set bootargs console=ttyAS0,115200 root=/dev/mtdblock0 rw rootfstype=jffs2 mem=128m coprocessor_mem=4m@0x10000000,4m@0x10400000 nwhwconf=device:eth0,hwaddr:$ethaddr init=/bin/devinit' set bootdesc_9 'UPDT ' set bootcmd_9 'run bootkern_9' set bootkern_9 'usb reset; fatload usb 0:1 a4000000 update; autoscr' set bootcmd 'bootmenu' set bootdesc_items 9 set bootmenutimeout 3 Freebox ENV bez mac: set bootdesc_0 USbA set bootcmd_0 'run bootargs_0; run bootkern_0' set bootkern_0 'usb reset; ext2load usb 0:1 a5000000 /boot/uImage; bootm a5000000' set bootargs_0 "set bootargs console=ttyAS0,115200 root=/dev/sda1 rw mem=128m coprocessor_mem=4m@0x10000000,4m@0x10400000 rootdelay=6 nwhwconf=device:eth0,hwaddr:${ethaddr} init=/bin/devinit" set bootdesc_1 USbb set bootcmd_1 'run bootargs_1; run bootkern_1' set bootkern_1 'usb reset; ext2load usb 0:1 a5000000 /boot/uImage; bootm a5000000' set bootargs_1 "set bootargs console=ttyAS0,115200 root=/dev/sdb1 rw mem=128m coprocessor_mem=4m@0x10000000,4m@0x10400000 rootdelay=6 nwhwconf=device:eth0,hwaddr:${ethaddr} init=/bin/devinit" set bootdesc_2 Hdd1 set bootcmd_2 'run bootargs_2; run bootkern_2' set bootkern_2 'ide reset; ext2load ide 0:1 a5000000 /boot/uImage; bootm a5000000' set bootargs_2 "set bootargs console=ttyAS0,115200 root=/dev/sda1 rw mem=128m coprocessor_mem=4m@0x10000000,4m@0x10400000 rootdelay=2 nwhwconf=device:eth0,hwaddr:${ethaddr} init=/bin/devinit" set bootdesc_3 Hdd2 set bootcmd_3 'run bootargs_3; run bootkern_3' set bootkern_3 'ide reset; ext2load ide 0:2 a5000000 /boot/uImage; bootm a5000000' set bootargs_3 "set bootargs console=ttyAS0,115200 root=/dev/sda2 rw mem=128m coprocessor_mem=4m@0x10000000,4m@0x10400000 rootdelay=2 nwhwconf=device:eth0,hwaddr:${ethaddr} init=/bin/devinit" set bootdesc_4 Hdd3 set bootcmd_4 'run bootargs_4; run bootkern_4' set bootkern_4 'ide reset; ext2load ide 0:3 a5000000 /boot/uImage; bootm a5000000' set bootargs_4 "set bootargs console=ttyAS0,115200 root=/dev/sda3 rw mem=128m coprocessor_mem=4m@0x10000000,4m@0x10400000 rootdelay=2 nwhwconf=device:eth0,hwaddr:${ethaddr} init=/bin/devinit" set bootdesc_5 NAnd set bootcmd_5 'run bootargs_5; run bootkern_5' set bootkern_5 'nand read.i 0xa5000000 0x3c00000 0x300000; bootm a5000000' set bootargs_5 "set bootargs console=ttyAS0,115200 root=/dev/mtdblock0 rw rootfstype=jffs2 mem=128m coprocessor_mem=4m@0x10000000,4m@0x10400000 nwhwconf=device:eth0,hwaddr:${ethaddr} init=/bin/devinit" set bootdesc_6 PKTN set bootcmd_6 'run bootargs_6; run bootkern_6' set bootkern_6 'nand read.i 0xa5000000 0x0 0x300000; bootm a5000000' set bootargs_6 "set bootargs console=ttyAS0,115200 root=/dev/mtdblock3 rw rootfstype=jffs2 mem=128m coprocessor_mem=4m@0x10000000,4m@0x10400000 nwhwconf=device:eth0,hwaddr:${ethaddr} init=/bin/devinit" set bootdesc_7 NFS set bootcmd_7 'run bootargs_7; run bootkern_7' set bootkern_7 'nfs a5000000 192.168.2.100:/opt/NBOX/release/boot/uImage;bootm a5000000' set bootargs_7_1 "console=ttyAS0,115200 root=/dev/nfs nfsroot=/opt/NBOX/release,tcp rw ip=192.168.2.200:192.168.2.100:192.168.2.1:255.255.255.0:nbox:eth0:off" set bootargs_7 "set bootargs $bootargs_7_1 mem=128m coprocessor_mem=4m@0x10000000,4m@0x10400000 nwhwconf=device:eth0,hwaddr:${ethaddr} init=/bin/devinit" set bootdesc_8 b4-u set bootcmd_8 'run bootkern_8' set bootkern_8 'protect off all; erase a02e0000 a02fffff; cp.b a0000080 a02e0000 4; reset' set serverip 192.168.2.100 set ipaddr 192.168.2.200 set bootcmd 'bootmenu 2000' set boot_default 0 saveenv vfd -OK- stop

Witka wszystkim. Od dłuższego czasu zmagam się z dziwnym zachowaniem mojego uboota. Po zakupie mój nBox po podłączeniu do sieci zgłaszał się jako "Uboot 1.3.1 057". Upewniało mnie to w przekonaniu, że mam załadowany uboot Freebox'a. Z tego co pamiętam w menu wyboru nośnika do bootowania była jedna pozycja z frazą "b4t". Nie pamiętam dokładnie bo to było ponad rok temu. Po pewnym czasie straciłem możliwość wyboru nośnika podczas bootowania, a zamiast "Uboot 1.3.1 057" na wyświetlaczu tuner mnie wita po starcie komunikatem "nbox". Co oznacza zwykle, że na pokładzie siedzi uboot od B4T. Chciałem próbnie załadować ENV od nowa, ale nie chcę tego schrzanić i wciąż nie jestem pewien czy uboot który mam to freebox, b4t a może multiboot (Nbox Duo_Multiboot FreeBoxB4_team 03_2012 Wersja1b lub Nbox5800 Duo_Multiboot_v2 Multi MAC 09_2013). W tej chwili po podłączeniu zasilania nBox wita mnie komunikatem "nbox" a następnie "Hdd1". Brak możliwości wyboru strzałkami innej opcji bootmenu. Postanowiłem sprawdzić co mi "powie" tuner przez złącze debug. Nie rozjaśniło to moich wątpliwości. Log z debug wygląda tak: 0 Reset IDE: Bus 0: OK Device 0: Model: ST3250820SCE Firm: 3.ACD Ser#: Q91ERDN8 Type: Hard Disk Supports 48-bit addressing Capacity: 238475.1 MiB = 232.8 GiB (488397168 x 512) 1872957 bytes read ## Booting image at a5000000 ... Image Name: Linux-2.6.32.59_stm24_0211 Image Type: SuperH Linux Kernel Image (gzip compressed) Data Size: 1872893 Bytes = 1.8 MiB Load Address: 84001000 Entry Point: 84002000 Verifying Checksum ... OK Uncompressing Kern Starting kernel console=ttyAS0,115200 root=/dev/sda1 rw ip=192.168.0.102:192.168 .0.1:192.168.0.1:255.255.255.0:eth0:off mem=128m coprocessor_mem=4m@0x10000000,4 m@0x10400000 rootdelay=6 nwhwconf=device:eth0,hwaddr:00:03:91:88:76:25 init=/bin /devinit - 0x00000000 - 0 ... INIT: version 2.88 booting INIT: Entering runlevel: 5 Uruchamiam: Graterlia OS Cała wolna pamiec RAM przydzielona do /tmp Mount /dev in tmpfs Copying device nodes to /dev Uruchamiam: Graterlia BoxType rcstype: ADB5800 boxtype: BSLA Uruchamiam: Graterlia Front Panel Uruchamiam: Graterlia Check FS fsck from util-linux 2.25 system was not cleanly unmounted, check forced. system: ***** REBOOT LINUX ***** system: 17304/61952 files (0.9% non-contiguous), 37480/246991 blocks /dev/sda3 fsck from util-linux 2.25 records: recovering journal records: clean, 1159/15138816 files, 1002331/60555009 blocks Nie ma partycji data Uruchamiam: Graterlia Frontpanel Start Info Mounting local filesystems... mount: mounting LABEL=data on /media/data failed: No such Cleaning /tmp /var/run. Hostname: sImBa-nBox. Uruchamiam: Graterlia STi Support init /dev symlinks init stmfb set stmfb load a/v firmware 4096+0 records in 4096+0 records out 4194304 bytes (4.0MB) copied, 0.066483 seconds, 60.2MB/s 4096+0 records in 4096+0 records out 4194304 bytes (4.0MB) copied, 0.061442 seconds, 65.1MB/s copLoadFile (file /lib/firmware/audio.elf) ustslave: Kernel Version: 24 base_address 0x10400000 seeking to 0 seeking to 5f00 seeking to 12320 seeking to 1aa20 seeking to 173100 seeking to 173138 seeking to 173170 seeking to 1b9058 seeking to 1b9060 seeking to 1b9068 seeking to 1b9070 seeking to 1d0920 seeking to 1d0a00 copLoadFile (file /lib/firmware/video.elf) ustslave: Kernel Version: 24 base_address 0x10000000 seeking to 0 seeking to 432c0 seeking to 59878 seeking to 598b0 seeking to 598e8 seeking to 5f3d8 seeking to 5f3e4 seeking to 5f3f0 seeking to 62664 seeking to 64700 init embx init AVS init player init frontends DVB-S init drivers init player2 set Video Output VIDEO:scart init SmartCard Reader Uruchamiam: Graterlia Boot Logo showSinglePic /boot/logo.mvi VIDEO_SELECT_SOURCE MEMORY (Success) VIDEO_PLAY (Success) VIDEO_CONTINUE: (Success) VIDEO_CLEAR_BUFFER: (Invalid argument) Uruchamiam: Graterlia Modules Init init Fan init CEC Start network Setting up IP spoofing protection: rp_filter. Configuring network interfaces... udhcpc (v1.22.1) started Sending discover... Sending discover... Sending select for 192.168.0.14... Lease of 192.168.0.14 obtained, lease time 86400 route: SIOCDELRT: No such process adding dns 194.168.4.100 adding dns 194.168.8.100 done. $Starting sshd:ok Starting portmap daemon.... Starting FTP server: vsftpd. Uruchamiam: Graterlia OpenVPN OpenVPN uruchomiony Uruchamiam: Graterlia Cron Cron włączony Uruchamiam: Graterlia NTP sh: sat: unknown operand Synchronizacja NTP 10 Oct 14:13:37 ntpdate[1895]: step time server 85.91.1.180 offset 466261969.943 585 sec Loading autofs Uruchamiam: Graterlia AutoFS Daemon Start MgCamd lighttpd[1937]: (log.c.166) server started lighttpd[1937]: (log.c.166) server started nored) Uruchamiam: Graterlia Remote Control init ADB5800 remote control Uruchamiam standardowy tryb obslugi pilota. lircd-0.9.0[1945]: lircd(default) ready, using /var/run/lirc/lircd /etc/init.d/rc: line 99: /etc/rc.d/rc5.d/S91rc.local: Permission denied lircd-0.9.0[1945]: accepted new client on /var/run/lirc/lircd Uruchamiam: Graterlia OpenPLi OpenPLi Starting... ________ __ .__ .__ / _____/___________ _/ |_ ___________| | |_ ___ / \ __\_ __ \__ \\ __\/ __ \_ __ \ | | \__ \ \ \_\ \ | \// __ \| | \ ___/| | \/ |_| |/ __ \_ \______ /__| (____ /__| \___ >__| |____/__(____ / \/ \/ \/ \/ login[1964]: root login on 'ttyAS0' BusyBox v1.22.1 (2014-09-11 11:19:38 CEST) built-in shell (ash) Enter 'help' for a list of built-in commands. Load OpenPLi GStreamer Framework sImBa-nBox:~# Podpowie ktoś co mam w takiej sytuacji zrobić? Nie wiem czy mam wgrać od nowa uboota, czy może wystarczy ENV? Ale nie wiem jakie ENV, bo nie jestem pewny jaki mam uboot na pokładzie. I problem się zapętla. Jeden kondensator wygląda na lekko spuchnięty (C95), ale tuner nie ma żadnych zawieszek czy zacinek i raczej nie mam z nim problemów prócz tego, że nie mogę wybrać innego nośnika jak Hdd1, na którym na szczęście mam G2 z którego jestem zadowolony.